No products in the cart
PUR TRUTH PREPARE QUICK-START GUIDE
1
Raise the bridges to the vertical position
2
Level the Truth Prepare using the built-in level on the bridge
3
Insert a pair of Truth Gates into the slots
4
Place a ball on the Ball Pad, get your putter and start warming up before your next round!
PARTS LIST
3 PUR Truth Gates Yellow (*Glow in the dark)
3 PUR Truth Fat Gates Red
2 PUR Truth Ghost Holes (*Glow in the dark)
LEVELING THE PREPARE
For accurate results it is important to find a level surface, specifically, the distance between the Ball Pad and the Truth Gates.
With the entire device flat on the ground, move the Truth Prepare around until you find an area that is level. The air bubble in the level should be directly in the middle of the level marks.
Once the bridge is in a level spot, slide the device forward at least to the point where the Ball Pad is in the original level spot you just identified.
Check the level on the bridge again to make sure the bridge remains level.
This process ensures that the area between the Truth Gates and the Ball Pad is level.
If the bubble in the bridge is off, start the process again until you have a level area from Ball Pad to the bridge and the Truth Gates.
TIPS: You will quickly realize that finding a perfectly level surface IS possible, but can be challenging. While the process can be frustrating, it is important for accurate training.
After the ball goes through the Truth Gates, the slope does not matter.
PUR BALL PAD
The Ball Pad is an optional but useful component engineered to precisely position the ball but not interfere with natural roll. The Ball Pad guarantees quick, accurate placement of the ball exactly in the center of the Prepare and Truth Gates.
Positioning the PUR Ball Pad: The further back from the Truth Gates the Ball Pad is positioned, the more difficult the putt. You may slide the Ball Pad back approximately 7 inches. When fully extended, the Ball Pad will click into place, with a button on each rail popping securely into the holes.
Practicing without the Ball Pad: To practice setting the ball up like you would in a normal round of golf, just remove the Ball Pad. Keep in mind, the margin of error between the Truth Gates is millimeters. If your ball is off-center by a millimeter, the feedback you are receiving can be misleading.
PUR TRUTH GATES
The PUR Truth Gates are designed to give you immediate, accurate feedback without disrupting your ball speed. Your most important focus when using the Truth Trainer is to putt the ball through the Truth Gates without touching them.
IMPORTANT: The Gates do not drop in from the top of the slots. They must be removed/inserted from underneath the Bridge.
To insert a Truth Gate, grab the pointed end of the Gate, push Gate up through one of the slots on the Bridge, then twist the Gate slightly and pull it down into the resting slot in Bridge.
To remove, grab the pointed bottom end of the Truth Gate, push up and release it from the slot, twist the gate slightly and then pull it down through the slot.
There are two sets of gates to change up your training difficulty:
PUR Truth Gates – thinner (yellow)
PUR Fat Gates – thicker (red)
PUR GHOST HOLE
The PUR Ghost Hole is the exact dimensions of a golf hole. Many believe, as a general rule of thumb, the speed of your putt should deliver the ball approximately one foot beyond the hole. The Ghost Hole offers precise feedback on whether you’re achieving this pace.
Create a hole wherever you want: Once you have found a level surface for the Trainer, you can create a golf hole in your living room or anywhere on the putting green. We strongly discourage you from trying to set up the Trainer in conjunction with a cut hole on the putting green because you will lose important training feedback on your pace.
TIP: Another reason to ‘create your own target’ is that you can putt on the green where it is not congested with other golfers. We also strongly discourage you from cutting a hole in your living room floor!
True Distance Control: It is impossible to judge your pace if you are practicing with a real golf hole: once the ball drops in the hole, it drops in the hole. The Ghost Hole eliminates this issue, allowing you to see the ball cross over the hole AND see its final resting distance, giving you accurate feedback on your true pace.
Start by hitting a couple of putts through the Trainer that do not hit the Truth Gates. Let the putts roll out to your desired length. You will immediately see the path of the ball and whether it breaks, etc.
With that information, simply place the Ghost Hole where your “made” putts would be. You now have your target hole for practice.
PACKING THE PREPARE IN THE CASE
Gently push together the rails until they are in the fully compressed position